Manage Milking Efficiency

Manage Milking Efficiency

To reduce mastitis and maintain milk quality, producers need to keep milking equipment in good working condition. However, milking efficiency should be considered from two other perspectives, the amount of time the milking cluster is attached to the udder (unit on time) and the percent of unit on time that milk is flowing at or near maximum. When milk isn’t flowing while the unit is attached, it is not only inefficient, but more importantly, damages the teat tissue, which could increase the risk of mastitis and decrease milk yield.

Regular Maintenance

A majority of dairy farms have their milking equipment evaluated and maintained on a routine basis. Although proper equipment function is necessary for milking efficiency, it does not necessarily guarantee it. Two management areas that could lead to poor milking efficiency are milking routines that don’t achieve consistent milk let down and overmilking. Either one of these problems can leave cows “high and dry” for a period of time and expose teats to high vacuum levels. In this article, we’ll discuss the first of these issues: poor milk let down or what is commonly called bimodal milking.

During teat stimulation before milking, nerves carry an electric signal to the brain. The brain then releases oxytocin into the blood and then to the udder. It takes about 1 to 2 minutes for oxytocin levels to increase in blood to optimally contract muscle cells around the milk ducts, which then squeeze the milk down toward the teats. The two important points about this oxytocin release are enough teat stimulation (at least 10 seconds of actual physical touching) and the duration of the lag time, that is, the time interval between when teats are first stimulated until the cluster is attached. Unfortunately, with increasing herd size, the number of cows that can be milked through the parlor per hour is often identified as one of the choke points of herd capacity. Thus, parlor efficiency is emphasized at the expense of milking efficiency.

Measure Milk Flow

How would you know if this is happening in your herd? One method is to measure milk flow with digital vacuum recorders (VaDia, Biocontrol NA). VaDia units record vacuum in the mouthpiece chamber (at the opening of the liner) and in the cluster. VaDia units don’t measure milk flow directly but give us a qualitative snapshot on milk flow. A simple way to interpret VaDia results relative to milk flow is:

  • High Milk Flow = Low vacuum in the liner or cluster
  • Low Milk Flow = High vacuum in the liner or cluster

VaDia units can measure vacuum levels at four places on the cluster simultaneously. We often measure vacuum in the mouthpiece of a front and rear liner, near the cluster and in a short pulsation tube.

Cow 1 (chart below) was ready to milk; the vacuum in the liner mouthpiece near the teat (red and blue lines) dropped quickly (less than 10 seconds after the unit was attached) and remained low until each teat was finished milking (the front quarter [blue line], finished before the rear quarter [red line]).

*Cow 1: The vacuum in liner mouthpiece drops to low level immediately after unit is attached. The cow was ready to milk.

For Cow 2 (chart below), the vacuum in the liner mouthpiece and cluster (green line) decreased, but then increased to near maximum levels, and finally decreased again. This cow was not ready to milk; milk flow was low for more than a minute after the milking unit was attached, signifying bimodal milk let down.

So how does bimodal milking relate to milking efficiency? For Cow 1, milk was flowing for about 4 minutes and 30 seconds of the total unit on time of 4 minutes and 45 seconds. Thus, the efficiency of this milking was 95%. For cow 2, milk was flowing for about 2 minutes of the total 3 minutes and 15 seconds the unit was attached, or a milking efficiency of about 60%.

Research from Wisconsin found when teats are subjected to high vacuum (Cow 2) blood is congested within the teat, the diameter of the teat canal decreases, which then decreases milk flow (Penry et al., 2018). This can be detrimental to the heath of the teat tissue and possibly impair both immune defenses of the teat and milk yield.

In the case of Cow 2, for all her milk to be harvested during the milking, she would have had to compensate with a higher milk flow rate in a shorter amount of time, despite the anatomical changes to her teat during high vacuum, which is unlikely.

A proper premilking routine should result in having at least 90% of cows with immediate milk let down after cluster attachment and milk should be flowing 95% of the time while the cluster is attached.

Dairy Herd Management, May 2018

By: Ron Erskine, DVM, Ph.D Michigan State


Tags: Management Tips, Milk Quality